Compaq StorageWorks TM RAID Array 3000 Pedestal Storage Subsystem Manuale di Servizio Pagina 282
- Pagina / 422
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
To connect the drive robotics and one drive to one shared SCSI bus and the
second drive to a second shared SCSI bus, follow these steps:
1. Connect a BN21K or BN21L between the last trilink connector on one
shared SCSI bus to the leftmost connector (as viewed from the rear) of
the TL892.
2. Connect a BN21K or BN21L between the last trilink connector on the
second shared SCSI bus to the left DLT2 connector (the fifth connector
from the left).
3. Install a 30-centimeter (11.8-inch) SCSI bus jumper between the
rightmost robotics connector (the second connector from the left) and
the left DLT1 connector (the third connector from the left).
4. Install an H879-AA terminator on the right DLT1 connector (the fourth
connector from the left) and install another H879-AA terminator on the
right DLT2 connector (the rightmost connector).
Figure 8–10 shows an example of a TruCluster Server cluster with a TL892
connected to two shared SCSI buses.
8–28 Configuring a Shared SCSI Bus for Tape Drive Use
- TruCluster Server 1
- Contents 3
- UltraSCSI Hardware 4
- Hardware 5
- 6 Using Fibre Channel Storage 6
- Contents vii 7
- Server Configuration 8
- Contents ix 9
- Contents xi 11
- Terminated Shared SCSI Buses 12
- Examples 12
- Contents xiii 13
- Contents xv 15
- Contents xvii 17
- About This Manual 19
- Related Documents 20
- About This Manual xxi 21
- About This Manual xxiii 23
- G Manuals for general users 24
- Reader’s Comments 25
- Conventions 26
- Introduction 27
- 1.2 Memory Requirements 28
- 1.3 Minimum Disk Requirements 28
- 1–4 Introduction 30
- 1.4 Generic Two-Node Cluster 31
- Memory Channel 32
- Shared SCSI Bus 32
- 1–8 Introduction 34
- Introduction 1–9 35
- 1–10 Introduction 36
- Increased Disk Configurations 37
- 1–12 Introduction 38
- Introduction 1–13 39
- System Boot Disks 40
- Introduction 1–15 41
- 1–16 Introduction 42
- Introduction 1–17 43
- 1–18 Introduction 44
- Introduction 1–19 45
- 1.6 Eight-Member Clusters 46
- Introduction 1–21 47
- ZK-1748U-AI 51
- P00>>> 53
- 2.4 Disk Device Restrictions 58
- 2.6 SCSI Signal Converters 60
- 2.8 SCSI Cables 62
- 3.2 SCSI Bus Performance 68
- 3.2.3 Data Path 69
- 3.2.4 Bus Speed 69
- CXO5744A 72
- 3.6 UltraSCSI Hubs 72
- Differential symbol 74
- ZK-1412U-AI 74
- ZK-1448U-AI 78
- ZK-1447U-AI 79
- Failover 85
- DWZZH UltraSCSI Hub 92
- ZK-1480U-AI 95
- Using UltraSCSI Hardware 99
- Configuration 100
- # umount /mnt 103
- Radial Configuration 105
- Commands 108
- KZPBA-CB SCSI ID 112
- ZK-1451U-AI 116
- Interconnect 117
- 5.1.2 MC2 Jumpers 119
- ZK-1197U-AI 125
- ZK-1530U-AI 136
- ZK-1522U-AI 137
- Replaced 138
- Adapter in Second System 139
- Memory Channel Adapters 140
- Second System 141
- Configuration (cont.) 144
- Using Fibre Channel Storage 147
- 6.1 Fibre Channel Overview 148
- ZK-1534U-AI 151
- ZK-1536U-AI 152
- ZK-1535U-AI 153
- ZK-1531U-AI 155
- ZK-1697U-AI 156
- ZK-1707U-AI 158
- ZK-1765U-AI 159
- ZK-1706U-AI 161
- ZK-1806U-AI 162
- AlphaServer 162
- ZK-1814U-AI 163
- 6.5 Zoning 164
- 6.5.2 Types of Zoning 165
- 6.5.3 Zoning Example 166
- ZK-1709U-AI 167
- 6.6 Cascaded Switches 167
- ZK-1795U-AI 168
- ZK-1794U-AI 169
- Adapter Module 182
- Reformatting nvram 185
- POO>>> init 186
- Installation 188
- set to 0 and the 194
- 6.9.1 Before You Install 199
- Cluster Member 217
- Multiple-Bus Failover Mode 222
- Failover Mode 223
- as follows: 224
- Information 228
- # emxmgr 231
- ZK-1749U-AI 235
- ZK-1750U-AI 238
- ZK-1751U-AI 239
- SCM_E0> show csb 248
- 1 2 3 4 5 6 248
- 2 Type of CSB node: 249
- Drive Use 255
- TZ88N−VA 257
- 8.1.2 Cabling the TZ88N-VA 258
- Interface 259
- 8.1.4 Cabling the TZ88N-TA 260
- DS−TZ89N−VW 262
- 20/40 GB DLT Tape Drive 266
- ZK-1461U-AI 276
- Shared SCSI Usage 278
- Member System 2 287
- Member System 1 287
- DLT0 Idle 289
- DLT1 Idle 289
- Loader Idle 289
- 0>__________<9 289
- DLT2 Idle 290
- DLT3 Idle 290
- 26>__________<35 290
- Shared SCSI Bus Usage 292
- ZK-1324U-AI 295
- ZK-1625U-AI 297
- ZK-1397U-AI 302
- 8.11.2 MUC Switch Functions 305
- 8.11.4 Tape Drive SCSI IDs 306
- ZK-1326U-AI 308
- ZK-1327U-AI 309
- ZK-1627U-AI 320
- Expansion Modules 323
- 8.13.1 General Overview 327
- Bus Usage 329
- SCSI Bulkhead 330
- ZK-1705U-AI 330
- Non-UltraSCSI Devices 333
- Termination 335
- Termination (cont.) 340
- Console Commands 341
- KZPSA-BB and KZPBA-CB SCSI ID 345
- P00>>> boot dka600 350
- Configurations Using External 353
- Non-UltraSCSI Devices 10–3 355
- ZK-1576U-AI 356
- 1 2 3 4 5 6 7 357
- Non-UltraSCSI Devices 10–7 359
- FRONT VIEW 360
- REAR VIEW 360
- 10.3.1 BA350 Storage Shelf 361
- ZK-1338U-AI 362
- Non-UltraSCSI Devices 10–11 363
- ZK-1339U-AI 364
- ZK-1529U-AI 365
- External Termination 366
- Non-UltraSCSI Devices 10–17 369
- Non-UltraSCSI Devices 10–19 371
- Non-UltraSCSI Devices 10–23 375
- Non-UltraSCSI Devices 10–27 379
- Non-UltraSCSI Devices 10–29 381
- Cluster Interconnect 383
- Non-UltraSCSI Devices 10–35 387
- DS-DWZZH-03 388
- ZK-1767U-AI 389
- Shared SCSI Buses 11–1 391
- Shared SCSI Buses 11–3 393
- Shared SCSI Cluster 395
- Shared SCSI Buses 11–7 397
- Shared SCSI Buses 11–11 401
- Shared SCSI Buses 11–13 403
- ZK-1846U-AI 404
- Figure 11–4 405
© 2020, manymanuals.it. Tutti i diritti riservati | 0.087 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale